SKU: 96667
Shop with confidence! This product has been fully inspected to avoid any buyer surprises. Read our in-depth product listing below.
Your purchase will NOT include: This product is pre-owned and may not include the same accessories as a new, unused unit. - other accessories not shown or listed here.Levelled the autoclave for proper chamber filling, connected it to a 120 volt power source, added distilled water and calibrated the temperature and pressure sensors. Calibration was successful, then proceeded to run test cycles on the sterilizer. Ran the autoclave through all it's preset sterilizing and drying cycles several times. To verify that this sterilizer is achieving it's required maximum sterilizing temperature, it was tested using a Max Register Thermometer, and found to exceed the required 270 F during a sterilization cycle. Prior to testing, this autoclave had it's Reservoir Tank cleaned and flushed, and a new Reservoir Cap, Safety Valve and Air Jet Valve were installed. Installed new Fill, Air, Exhaust and Dump Valve Coil Pack and Dump Valve Solenoids. Installed a new AJUNC-3 Analog Control board and Pressure Transducer. Cleaned the sterilizing chamber and installed a new Door Gasket, Door Bellows Assembly and Filter Screen. Installed a new HEPA Air Drying Filter and Cap. Cleaned the sterilizing trays and rack. Autoclave is fully functioning and in good condition.
Technician Testing Notes
Levelled the autoclave for proper chamber filling, connected it to a 120 volt power source, added distilled water and calibrated the temperature and pressure sensors. Calibration was successful, then proceeded to run test cycles on the sterilizer. Ran the autoclave through all it's preset sterilizing and drying cycles several times. To verify that this sterilizer is achieving it's required maximum sterilizing temperature, it was tested using a Max Register Thermometer, and found to exceed the required 270 F during a sterilization cycle. Prior to testing, this autoclave had it's Reservoir Tank cleaned and flushed, and a new Reservoir Cap, Safety Valve and Air Jet Valve were installed. Installed new Fill, Air, Exhaust and Dump Valve Coil Pack and Dump Valve Solenoids. Installed a new AJUNC-3 Analog Control board and Pressure Transducer. Cleaned the sterilizing chamber and installed a new Door Gasket, Door Bellows Assembly and Filter Screen. Installed a new HEPA Air Drying Filter and Cap. Cleaned the sterilizing trays and rack. Autoclave is fully functioning and in good condition.
Levelled the autoclave for proper chamber filling, connected it to a 120 volt power source, added distilled water and calibrated the temperature and pressure sensors. Calibration was successful, then proceeded to run test cycles on the sterilizer. Ran the autoclave through all it's preset sterilizing and drying cycles several times. To verify that this sterilizer is achieving it's required maximum sterilizing temperature, it was tested using a Max Register Thermometer, and found to exceed the required 270 F during a sterilization cycle. Prior to testing, this autoclave had it's Reservoir Tank cleaned and flushed, and a new Reservoir Cap, Safety Valve and Air Jet Valve were installed. Installed new Fill, Air, Exhaust and Dump Valve Coil Pack and Dump Valve Solenoids. Installed a new AJUNC-3 Analog Control board and Pressure Transducer. Cleaned the sterilizing chamber and installed a new Door Gasket, Door Bellows Assembly and Filter Screen. Installed a new HEPA Air Drying Filter and Cap. Cleaned the sterilizing trays and rack. Autoclave is fully functioning and in good condition.
Product Condition
- Manufacturer: Tuttnauer
- Model: EZ9
- Serial Number: 1207126
- Power Requirements: 120V
- Year: 2012
- Timer Function: Not available
- Controls: Not available
- Cycle Count: Not available
- Software Version:
Item Includes:
1 - Tuttnauer EZ9 Autoclave - Steam Sterilizer 3 - Sterilizing Trays w/ Rack 1 - Drain Hose 1 - Power Cord
Item Excludes:
This product is pre-owned and may not include the same accessories as a new, unused unit.
1 - Tuttnauer EZ9 Autoclave - Steam Sterilizer 3 - Sterilizing Trays w/ Rack 1 - Drain Hose 1 - Power Cord
Item Excludes:
This product is pre-owned and may not include the same accessories as a new, unused unit.
Shipping calculated at checkout.
30 Day Return Guarantee
Your satisfaction is important to us: Have your equipment installed by a factory-trained technician or Atlas-approved vendor to qualify for our return policy.See our Terms and Conditions of Sale for details.